RETROPLANE.net Index du Forum
FAQ - Charte - Rechercher - Fichiers - Membres - S'enregistrer - Annuaire - Vérifier ses messages privés - Connexion

SCHEIBE-LORAVIA TOPAZE 1:3.5 SCALE
Aller à la page
1, 2, 3 Suivante

 
Poster un nouveau sujet   Répondre au sujet    RETROPLANE.net Index du Forum -> Constructions Détaillées en Photo
Voir le sujet précédent :: Voir le sujet suivant  
Auteur Message
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 04/02/2010 00:20    Sujet du message: SCHEIBE-LORAVIA TOPAZE 1:3.5 SCALE Répondre en citant

For this project I am trying some new techniques. First of all I have constructed a fuselage jig from metal which I hope will be used for all my fuselages in the future. It consists of two lengths of 50 x 50mm L-section Aluminium bolted together, leaving a slot in the middle. Steel brackets slide up and down as required along the slot, making the setting up of a project very quick and simple. A steel tape measure is attached with double-sided tape for quick alignment of the fuselage formers. The total cost for the jig was around £60 for all the parts...










cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
de Schaetzen Harold
Maniaco Posteur
Maniaco Posteur


Inscrit le: 06 Avr 2006
belgium.gif

Localisation: Schilde
Âge: 78 Verseau

MessagePosté le: 04/02/2010 10:23    Sujet du message: Répondre en citant

Dear Chris,

Very interesting, this new technique.
We are following your new construction with close attention.

Good luck.

Harold
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
DELRIEUPierre
Psycho Posteur
Psycho Posteur


Inscrit le: 28 Jan 2006
france.gif

Localisation: Arvert 17530
Âge: 74 Poissons

MessagePosté le: 04/02/2010 14:14    Sujet du message: Répondre en citant

Intéressent effectivement comme méthode en plus il n'y a plus d’équerre que des équerres. Wink
Pierre
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail Visiter le site web de l'utilisateur
Jürgen
Fidèle Posteur
Fidèle Posteur


Inscrit le: 30 Déc 2007
germany.gif

Localisation: Rhein / Main (Darmstadt)
Âge: 57 Gémeau

MessagePosté le: 04/02/2010 17:58    Sujet du message: Répondre en citant

Hello Chris,
I also interesting for this famous method.
I think it can be a very good solution for all of us here
and I` am happy to follow your project in the next time.

Best regards
Jürgen
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 04/02/2010 20:14    Sujet du message: Répondre en citant

Merci messieurs...I should say that the jig is not of my invention, I have copied from a fellow UK modeller, with a few modifications of my own Wink

The next new method I am trying is to design the Loravia in CAD. But how? I know nothing about CAD?

Then I came across Devfus from the DevCad website, which is a way for beginners to design fuselages on the computer. This allows you to blend different former shapes to give a smooth transition throughout the fuselage.
It is not easy to use, but the results are very promising. The best feature is the 3D preview at each stage, so that you can see if you are getting it right before you cut any wood...






The programme also calculates the jig supports, excellent for my new jig...!
You can download a free trial version from here: http://www.devcad.com/eng/default.htm






cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Olli
Incurable Posteur
Incurable Posteur


Inscrit le: 22 Juil 2006
germany.gif

Localisation: Germany
Âge: 56 Verseau

MessagePosté le: 04/02/2010 20:32    Sujet du message: Répondre en citant

Hello Chris a wonderful project.

Look here my construction of the SF-27.
It is designed in 2D.
http://www.rc-network.de/forum/showthread.php?t=179405&highlight=sf-27










Best Regards Olli
www.oliver-theede-oldtimersegler.de
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail Visiter le site web de l'utilisateur
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 05/02/2010 00:20    Sujet du message: Répondre en citant

Nice Olli...have you started to cut wood yet...?


cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Olli
Incurable Posteur
Incurable Posteur


Inscrit le: 22 Juil 2006
germany.gif

Localisation: Germany
Âge: 56 Verseau

MessagePosté le: 05/02/2010 16:43    Sujet du message: Répondre en citant

Hello Chris

i have not yet made parts of wood.
I'm not quite finished with the Konstuktion.
In the moment I'm building my A-Spatz in M 1:2.5.

Best Regards Olli
www.oliver-theede-oldtimersegler.de
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail Visiter le site web de l'utilisateur
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 05/02/2010 21:31    Sujet du message: Répondre en citant

Olli, I am working between Profili, Devfus and Illustrator to produce my drawings...



So, we start to cut wood. The jig supports are made from cheap CTP from my local timber yard...(All the parts are cut by hand with my scroll saw, of course)



Now the formers are set up on the jig...


Et, voila!







cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Olli
Incurable Posteur
Incurable Posteur


Inscrit le: 22 Juil 2006
germany.gif

Localisation: Germany
Âge: 56 Verseau

MessagePosté le: 06/02/2010 09:33    Sujet du message: Répondre en citant

Hello Chris

yor work is perfect.
I am planning the SF-27 than SF-27 M to build.
Here you can see a animation from the engine as open and cloused.
http://www.oliver-theede-oldtimersegler.de/klappmechaniktest.gif

Best Regards Olli
www.oliver-theede-oldtimersegler.de
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail Visiter le site web de l'utilisateur
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 06/02/2010 11:54    Sujet du message: Répondre en citant

Nice, Olli...

Now the diagonal 6mm sq. balsa is added to make the rear of the fuselage rigid...



A strip of 1.5mm CTP is added to give a clean joint between the front glassfibre and rear fabric of the fuselage...



Then, the 1.5 CTP planking at the front can be added...





cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
espenlaub
Fidèle Posteur
Fidèle Posteur


Inscrit le: 01 Juil 2008
germany.gif


MessagePosté le: 06/02/2010 12:46    Sujet du message: Répondre en citant

sehr schönes Projekt!





Gruß
Espenlaub[/img]
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Olli
Incurable Posteur
Incurable Posteur


Inscrit le: 22 Juil 2006
germany.gif

Localisation: Germany
Âge: 56 Verseau

MessagePosté le: 06/02/2010 12:54    Sujet du message: Répondre en citant

Hallo Espenlaub,

das Bild welches Du da zeigst ist ein Bestandteil meiner Unterlagen
für meine Konstruktion.
Ich werde die SF-27 M 1:2,5 aber leider noch lange nicht bauen können,
mein Fliegerlager platzt aus allen Nähten Crying or Very sad
Vielleicht irgend wann ein mal.

Gruß Olli
www.oliver-theede-oldtimersegelr.de
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail Visiter le site web de l'utilisateur
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 07/02/2010 09:52    Sujet du message: Répondre en citant

Now, it is time to start making the all-moving-tail (AMT)
















cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 08/02/2010 17:59    Sujet du message: Répondre en citant

It seems a good idea to set up the fin and AMT while the fuselage is still on the jig so that they can be set up accurately...


So now the fin and rudder construction commence...







cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Paul ELLIS
Fidèle Posteur
Fidèle Posteur


Inscrit le: 24 Oct 2007
france.gif

Localisation: Haute Vienne, Limousin
Âge: 77 Verseau

MessagePosté le: 08/02/2010 20:05    Sujet du message: Répondre en citant

I love the jig Chris.

I suppose the fuselage can be left on until it's time to clad the bottom.

No more bananas!

BTW I suppose you realise that you're turning into a computer Nerd, don't you. MDR

Me? I think they're just a passing fad.

Paul



Un anglais en France
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Visiter le site web de l'utilisateur
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 08/02/2010 21:22    Sujet du message: Répondre en citant

Actually, Devfus will also calculate an upside down position on the jig: might try that next time...




cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 09/02/2010 23:06    Sujet du message: Répondre en citant

Some filler for the base of the fin now...


and now the rear end is almost complete...


The fuselage can now be removed from the jig...


and the lower ctp planking completed...




cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Orionis
Incurable Posteur
Incurable Posteur


Inscrit le: 31 Aoû 2006
france.gif

Localisation: Drôme
Âge: 57 Bélier

MessagePosté le: 10/02/2010 08:27    Sujet du message: Répondre en citant

Shocked Do you sometimes sleep, Chris? Wink


Fabrice
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Visiter le site web de l'utilisateur
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 10/02/2010 21:58    Sujet du message: Répondre en citant

Fabrice, I have a microwave bed...8 hours sleep in 10 minutes (Old joke!)


cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 12/02/2010 21:20    Sujet du message: Répondre en citant

The two main longerons that located on the jig are now removed...



With the remporay formers removed, the inside of the fuselage can be glassed...


1/2-round hardwood mouldings are glued to the 6mm square longerons to simulate the metal tube of the full-size...




cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 17/02/2010 00:25    Sujet du message: Répondre en citant

A quick look at the wings, as they are fairly simple to make...

The new jig is also very useful for holding the wing spars straight while they are marked out for tapering...




The brass wing-joiner boxes are angled inside the spars for a straight join...







cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
fceed
Fidèle Posteur
Fidèle Posteur


Inscrit le: 20 Fév 2006
france.gif

Localisation: Besançon

MessagePosté le: 17/02/2010 11:00    Sujet du message: LCA-10 or LCA-11 Répondre en citant

The pictures on the wall indicate that the egyptian decoration of the F-CEEM takes your attention. Note that F-CEEM is a LCA-11 and the wings are completely covered with plywood without fabric. F-CEED is a LCA-10, the wings are partially covered with fabric as indicated on your drawing.


airef
La théorie, c'est quand on sait tout et que rien ne fonctionne. La pratique, c'est quand tout fonctionne et que personne ne sait pourquoi. Nous avons réuni théorie et pratique : Rien ne fonctionne... et personne ne sait pourquoi !
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Visiter le site web de l'utilisateur
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 17/02/2010 20:22    Sujet du message: Répondre en citant

Merci fceed, more stuff I didn't know [argh] I started with Martin Simons SF27M drawing, then found Richard Ferriere's website, now I discover there is an LCA 11! My model will therefore incorporate elements of all three.
Not to worry though, my main purpose is to build her under 7Kgs for slope flying in light winds, and I'm sure she will look pretty there anyway...



cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 20/02/2010 18:21    Sujet du message: Répondre en citant

I won't detail the wing construction too much, as they are all pretty much the same...
So, making up the canopy frame. the long pieces (2 of 3 x 6mm spruce) are laminated against the sides of the fuselage to obtain the correct shape


Marking out the curve of the wing root fairing...



Balsa is used for the main shape...


and finished with glass cloth and polyester resin...


The Flamingo canopy is a perfect fit Very Happy Very Happy Very Happy




cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
cw
Accro Posteur
Accro Posteur


Inscrit le: 06 Juil 2008
uk.gif

Localisation: Blandford, Dorset, Southern England
Âge: 76 Sagittaire

MessagePosté le: 22/02/2010 21:45    Sujet du message: Répondre en citant

The airbrakes are as simple as I can possibly make them...



Now to make a BIG hole in the wing!



Airbrake installed...




I started this project over the Christmas holiday, now, with this last picture we are up to date and in real time (Pic taken yesterday)




cw
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
erwan
Psycho Posteur
Psycho Posteur


Inscrit le: 17 Aoû 2006
france.gif


MessagePosté le: 23/02/2010 06:26    Sujet du message: Répondre en citant

So fast and so nice. [bave]

erwan
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
Orionis
Incurable Posteur
Incurable Posteur


Inscrit le: 31 Aoû 2006
france.gif

Localisation: Drôme
Âge: 57 Bélier

MessagePosté le: 23/02/2010 08:45    Sujet du message: Répondre en citant

She will probably fly this week-end... [clap]


Fabrice
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Visiter le site web de l'utilisateur
Paul ELLIS
Fidèle Posteur
Fidèle Posteur


Inscrit le: 24 Oct 2007
france.gif

Localisation: Haute Vienne, Limousin
Âge: 77 Verseau

MessagePosté le: 23/02/2010 09:18    Sujet du message: Répondre en citant

Lovely work Chris (Comme d'habitude)

You're well on schedule for another 6 this year. Wink

Paul



Un anglais en France
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Visiter le site web de l'utilisateur
Jürgen
Fidèle Posteur
Fidèle Posteur


Inscrit le: 30 Déc 2007
germany.gif

Localisation: Rhein / Main (Darmstadt)
Âge: 57 Gémeau

MessagePosté le: 23/02/2010 18:07    Sujet du message: Répondre en citant

A good job, Chris !
Very, very good !


[amen] [amen] [amen]
Jürgen
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Montrer les messages depuis:   
Poster un nouveau sujet   Répondre au sujet    RETROPLANE.net Index du Forum -> Constructions Détaillées en Photo Toutes les heures sont au format GMT + 1 Heure
Aller à la page
1, 2, 3 Suivante
Page 1 sur 3

 
Sauter vers:  
Vous ne pouvez pas poster de nouveaux sujets dans ce forum
Vous ne pouvez pas répondre aux sujets dans ce forum
Vous ne pouvez pas éditer vos messages dans ce forum
Vous ne pouvez pas supprimer vos messages dans ce forum
Vous ne pouvez pas voter dans les sondages de ce forum
Vous ne pouvez pas joindre des fichiers
Vous pouvez télécharger des fichiers

Zone de Téléchargement du Forum et Site Retroplane


Images aléatoires album Retroplane, clic pour Agrandir

Forum en Flux RSS