RETROPLANE.net Index du Forum
FAQ - Charte - Rechercher - Fichiers - Membres - S'enregistrer - Annuaire - Vérifier ses messages privés - Connexion

Slingsby Gull scale 1/4
Aller à la page
1, 2, 3, 4, 5, 6 Suivante

 
Poster un nouveau sujet   Répondre au sujet    RETROPLANE.net Index du Forum -> Constructions Détaillées en Photo
Voir le sujet précédent :: Voir le sujet suivant  
Auteur Message
hermann
Maniaco Posteur
Maniaco Posteur


Inscrit le: 25 Mai 2006
france.gif

Localisation: Région Parisienne

MessagePosté le: 18/08/2019 09:48    Sujet du message: Répondre en citant

Bonjour Vincent.
Je découvre seulement maintenant ton nouveau projet Embarassed
Bravo c'est super [clap] [clap] [clap] très belle machine.
J'adore la réalisation du fuselage et ta technique de mise en forme des couples. [amen] [amen]
Ca va être un très beau modèle.
Bonne continuation
Charles
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 18/08/2019 16:10    Sujet du message: Répondre en citant

Merci Pierre et Hermann

Thanks a lot for your encouraging remarks.
I had doubts about the construction of the tailplane, but it turned out OK.
It is very, very stiff, also in torsion.
The original builders understood very well how to build with ply!

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
de Schaetzen Harold
Maniaco Posteur
Maniaco Posteur


Inscrit le: 06 Avr 2006
belgium.gif

Localisation: Schilde
Âge: 78 Verseau

MessagePosté le: 19/08/2019 08:50    Sujet du message: Répondre en citant

Beste Vincent,

Ik ben ook onder de indruk van jouw zeer interessante constructie.
Laminaat constructie is eigenlijk niet zo moeilijk om te gebruiken. Het vraagt een beetje geduld. Veel voorbereiding. Geeft een zeer sterkere resultaat.
Ik zie dat jij nog altijd zeer nauwkeurig en proper bouwt. Jouw beroep ben jij niet vergeten.

Mvg.
Harold
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 19/08/2019 14:50    Sujet du message: Répondre en citant

Dank je voor je vriendelijke woorden Harold!

Lamineren met (zeker met cyano) gaat erg makkelijk en snel en zoals je al zei, het is erg sterk en licht. Ik denk dat het met cyano minder sterk wordt dan met epoxy, maar het is erg makkelijk en relatief schoon. Ik heb het lamineren in de jachtbouw geleerd, vroeger gebruikten de scheepsbouwers zelfs kromme stukken boom voor de gebogen spanten, met lamineren bereik je eigenlijk hetzelfde.
Overigens staat het gemopper als dingen niet lukken niet op de foto's..... Wat je over mijn beroep opmerkte klopt wel, ik was gewend de hele dag met de hand te frezen, dat is wel aardig ingebakken.
Daarnaast ben ik er niet aan toegekomen om digitaal te tekenen en ook CNC te frezen.
Gelukkig heb ik vrienden die dat wel kunnen, zeker erg prettig bij de vleugelribben Very Happy

Mvg,
Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
jean-jacques stannard
Accro Posteur
Accro Posteur


Inscrit le: 21 Nov 2012
france.gif

Localisation: 62 Bavincourt
Âge: 71 Poissons

MessagePosté le: 19/08/2019 15:46    Sujet du message: slinsby gull Répondre en citant

Hello Vincent!
I love your way of building! It will necessarily be a good sail glider Very Happy Very Happy Very Happy
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 20/08/2019 08:39    Sujet du message: Répondre en citant

Hi Jean-Jacques,

I can only build in this way Confused Hope it will fly nice. The weight of the stabilizer is now 140gr.

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
de Schaetzen Harold
Maniaco Posteur
Maniaco Posteur


Inscrit le: 06 Avr 2006
belgium.gif

Localisation: Schilde
Âge: 78 Verseau

MessagePosté le: 21/08/2019 08:18    Sujet du message: Répondre en citant

Beste Vincent,

Ik kom even terug op jouw constructie techniek.

Ik ben verbaasd dat jij een voorkeur heb voor cyano. OK, en zeer snelle lijm, sterk, maar het moet van de 1ste keer exact staan. Geen aanpassing mogelijk. En met die verschillende "latjes naast mekaar" is dat niet eenvoudig.
Ik gebruik Pattex witte lijm, water bestendig. En dan nog veel geduld voor de droogtijd.

Mvg.
Harold
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 21/08/2019 10:19    Sujet du message: Répondre en citant

Beste Harold,

Je hebt helemaal gelijk, maar ik doe het iets anders. Uiteraard eerst folie op de tekening of ondergrond, dan buig en plaats ik alle latjes

zet er klemmetjes op

en als alles naar mijn zin is druppel ik er veel dunne cyano overheen


Als de cyano droog is, kan ik (in dit geval) het spant losmaken en eventueel wat cyano toevoegen. Ik heb dat ook met vochtige latjes gedaan. Voor spanten voldoet dit prima, gelamineerde liggers lijm ik wel met PVA of epoxy.

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
hermann
Maniaco Posteur
Maniaco Posteur


Inscrit le: 25 Mai 2006
france.gif

Localisation: Région Parisienne

MessagePosté le: 21/08/2019 10:49    Sujet du message: Répondre en citant

Bonjour Vincent,

Super les explications [clap] [clap] , comme je le disais , j'adore cette technique particulière et qui donne d'autres perspectives de pièces à fabriquer.
Seul petits soucis dans le cas du fuselage ou de pièces avec longerons est l'intégration dans la forme à obtenir ? Surement possible, mais avec quelques complications.
Pour la colle, c'est chacun son sentiment, moi j'aime bien l'époxy, mais c'est plus long et moins propre !! Je pense que la cyano a beaucoup d'avantages, on a un adepte sur Retroplane du collage cyano MDR
Excuse de répondre en Français mais le Néerlandais ou l'anglais ne sont pas ma tasse de thé.
Remarque : Google traduction passe très bien tous vos échanges avec Harold.
Ah ! j'oubliais : quel variété de bois utilises-tu là ?
Bonne continuation.
Charles
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 21/08/2019 12:33    Sujet du message: Répondre en citant

Bonjour Charles,

Je essaye en Francais.... merci pour votre comments!
Je pense le bois est pin. Normalement le magasin ou j'achete mon materiel a du Douglas fir.
I continue en Anglais, I use super thin cyano and because the gaps between the layers are very small, the glue is sucked in by capillary action. No hurry or stress, just put everything dry in position, add glue and almost immediately it hardens (sometimes smoking Very Happy )
I use this technique for fuselage frames and not so very much stressed parts. For building wing spars etc I use white glue (PVA) or epoxy with a suitable filler. (but I'cant use these above mentioned techniques)

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
caralp_laurent
Psycho Posteur
Psycho Posteur


Inscrit le: 30 Jan 2006
france.gif

Localisation: La Houssaye en Brie 77
Âge: 51 Gémeau

MessagePosté le: 21/08/2019 19:04    Sujet du message: Répondre en citant

« bocorvin » a écrit:
Hi Jean-Jacques,

I can only build in this way Confused Hope it will fly nice. The weight of the stabilizer is now 140gr.

Vincent


Hi Vincent Very Happy
Sure it will !! And will be beautiful too Wink

Have a good building,

Friendly


Lolo



Lolométéo, rétro addict ;o)

"On commence à vieillir quand on remplace ses rêves par des regrets"
Sénèque
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
de Schaetzen Harold
Maniaco Posteur
Maniaco Posteur


Inscrit le: 06 Avr 2006
belgium.gif

Localisation: Schilde
Âge: 78 Verseau

MessagePosté le: 22/08/2019 09:02    Sujet du message: Répondre en citant

Merci à Retroplane.
Merci à Vincent B.

Nous avons beaucoup de chance pour pouvoir partager nos différentes techniques de constructions.
Au delà des frontières et des différences de langues.
Et aussi grâce à Internet et le Web.
Harold

Very Happy Very Happy Very Happy
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 22/08/2019 16:17    Sujet du message: Répondre en citant

Completely right! Very Happy Very Happy Very Happy

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 11/09/2019 11:37    Sujet du message: Répondre en citant

Bonjour a tous,

I made a start with the wing. Because it has the form of a gull, the building board couldn't be flat. Also the "fold" isn't sharp, but its curved. This is my solution


I also made a very basic drawing of the wing, which is lying on this building board. In the meantime Rob draw the ribs, using the original profile, NACA 4416 (like the real glider). To optimize the gliding the profile gets thinner (12%) towards the nod. Adri CNC'd them from poplar ply, only the ribs at the root from birch ply. Thanks very much Adri and Rob [clap] [clap] [clap] , the milling makes building much nicer! We had some discussion about ribs built up from battens or just ply. Adri came up with a good alternative, he milled quite big apertures in the ribs, on which I could glue slats. Now there was some luck, the ribs of the original Petrel (a glider from the same builder as the Gull) were constructed in a similar way.

Most of the milled ribs

A tryout with slats of 2X2 mm, the 1X1mm are on backorder Sad coming soon I hope.




I went on with the mainspar, first the scarf joints

I learnt to make them in pairs, fits always! (The two short slats are glued to the worksurface, so its easier sanding)
Glued with slow curing epoxy and wooddust as filler

wrapped in thin foil



clamped together



and finished


Laminated into upper and lower spar. From 5 layers to 1 layer, glued with PVA. glue on the layers

the layers layed on top of each other

and clamped in shape

the finished spars, lying on the building board


Because I was waiting for the slats for the ribs, I started with the servo tray for the ailerons. The actuation will be with pull-pull wires, so I thought to place the servo in the root rib, so I could slide it out to adjust the wires

to the left, my first tryout...


Next thing thing were the airbrakes. The hinges of the original where a kind of piano hinges, so I tried to make something similar

















To be continued,

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 18/09/2019 19:41    Sujet du message: Répondre en citant

Hello everyone,

I went on with the fuselage. The intention was to make a load bearing skin, this gave some difficulties at the wing- fuselage connection. I also doubted about the carbon wingjoiner(s). I made a center section

which will be incorporated in the fuselage later

I also changed the short sections of the brass tube for full lengths pieces.

To get a better load distribution I laminated some partial bulkheads.





some internal reinforcements which I plan to use after the applying of the plywood skin, wait and see....



The cockpit was the next item






internal ply sheeting

the nose cone build up of 10mm balsa. It will be used as a core for the ply sheeting

looks not very well



the nose cone, with plenty of space for ballast


In the meantime I thought about the placing of the servo's and the towhook (for aerotow)The real one had the ring of the coupling at the first bulkhead and I decided it was better to make the coupling myself to create enough space for the feet of the pilot



all soldered with silver

its a 2mm steel pin sliding in brass





The only option to place the servo's was just behind the pilots seat

The elevator and rudder will be actuated with pull-pull wires



Most parts in a try-out . The brass tubes for the wingjoiners are already epoxied in place.


to be continued.

Vincent


Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
sebastian92
Serial Posteur
Serial Posteur


Inscrit le: 01 Sep 2015
france.gif

Localisation: Hauts de seine
Âge: 60 Scorpion

MessagePosté le: 18/09/2019 20:16    Sujet du message: Répondre en citant

[clap] nice job, very technical ! i like it Very Happy


Pourvu que ça vole, roule, flotte ! normalement j'ai tout bien fait pour…
Un bel avion est un avion qui vole bien ! Marcel Dassault
…………
Sebastian

Vends module émission 2.4 ghz pour Futaba, Hitec TZ-FM + 2 récepteurs corona 8 voies (contact en MP)
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 12/10/2019 08:54    Sujet du message: Répondre en citant

Bonjour a tous,
I went on with the ribs, finally the very thin battens (1 X 1mm) had arrived and I drawed the pattern for them on the ribs with pencil




The battens are cut off after glueing with a small wire cutter, and sanded.




Now I could built the wing itself





I like the curve in the wing!

to be continued,

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 26/10/2019 11:07    Sujet du message: Répondre en citant

Bonjour a tous,

After gluing in all the battens and vertical webs I went on with the hinges. I used the method of Vincent Besancon (sorry I don't have the French correction Sad ) and I pre cut the ribs



so I could glue the hinges in place before cutting of the aileron. Next I tried to figure out the pulleys of the pull pull wires

and getting the angles correct. The rudderhorns on the aileron have the same throw as the on the servo. I had to create a lot of space for the wires in the ribs at the root, even I had to reinforce one rib.

planning the pull pull wires

The actuation of the spoiler came quite close to the pull pull wires of the ailerons.



The servo arm is in its most extended position when the spoiler is closed, so there is less chance of burning the servo....
Laminated tip

and the trailing edge is built up of 0.8 mm ply bottom and top, balsa in between. I laminated the balsa also in the curve of the trailing edge





I guess there is less figuring out with the other wing Very Happy

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Sed
Maniaco Posteur
Maniaco Posteur


Inscrit le: 13 Mai 2015
france.gif

Localisation: Villeurbanne
Âge: 57 Taureau

MessagePosté le: 26/10/2019 14:26    Sujet du message: Répondre en citant

Perfect job as usual [amen] [amen] !


Serge
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
Olli
Incurable Posteur
Incurable Posteur


Inscrit le: 22 Juil 2006
germany.gif

Localisation: Germany
Âge: 56 Verseau

MessagePosté le: 26/10/2019 15:47    Sujet du message: Répondre en citant

Hi Vincent,

very nice build [clap] [clap]

Best Regards Olli



http://www.oliver-theede-oldtimersegler.de/
http://www.oliver-theede-oldtimersegler.de/oldtimerinteressengemeinschaft.htm


Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail Visiter le site web de l'utilisateur
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 26/10/2019 22:33    Sujet du message: Répondre en citant

Thanks Sed and Olli for your nice commets Very Happy Very Happy !

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Mad Doc
Accro Posteur
Accro Posteur


Inscrit le: 08 Juil 2014
germany.gif

Localisation: Wuppertal, Deutschland
Âge: 47 Scorpion

MessagePosté le: 31/10/2019 15:30    Sujet du message: Répondre en citant

Hello Vincent!!!
What a beautiful model, and what a nice work!
I´m sure it will look just nice in the air!
Greetings,
Christian
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 01/11/2019 12:32    Sujet du message: Répondre en citant

Hello Chtistian, thanks for your nice comment Very Happy .
In the meantime I went on with the other wing and that went indeed a lot faster! So yesterday I put it all together in the sunshine, its now raining Sad First in the attic (It just fits)


And outside












To be continued,

Vincent.


Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
de Schaetzen Harold
Maniaco Posteur
Maniaco Posteur


Inscrit le: 06 Avr 2006
belgium.gif

Localisation: Schilde
Âge: 78 Verseau

MessagePosté le: 01/11/2019 12:38    Sujet du message: Répondre en citant

Prachtig! Een echte kunstwerk.
[amen] [amen] [amen]
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
caralp_laurent
Psycho Posteur
Psycho Posteur


Inscrit le: 30 Jan 2006
france.gif

Localisation: La Houssaye en Brie 77
Âge: 51 Gémeau

MessagePosté le: 01/11/2019 13:30    Sujet du message: Répondre en citant

Wow, magnificent job Vincent !!!
[clap] [clap] [clap]

Friendly


Lolo



Lolométéo, rétro addict ;o)

"On commence à vieillir quand on remplace ses rêves par des regrets"
Sénèque
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 01/11/2019 14:31    Sujet du message: Répondre en citant

Merci Harold et Lolo,

Thanks for your nice comments!
Hopefully it will fly nice, Each wing is 650gr at this moment

To be continued,

Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
jean-jacques stannard
Accro Posteur
Accro Posteur


Inscrit le: 21 Nov 2012
france.gif

Localisation: 62 Bavincourt
Âge: 71 Poissons

MessagePosté le: 01/11/2019 15:19    Sujet du message: slingsby gull Répondre en citant

Very Happy Dreaming build !!!! [clap] [clap] [clap]
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
Johannes
Serial Posteur
Serial Posteur


Inscrit le: 23 Juil 2007
germany.gif

Localisation: Leichlingen
Âge: 64 Sagittaire

MessagePosté le: 01/11/2019 19:46    Sujet du message: Répondre en citant

Hallo Vincent,
Die Holzkonstruktion sieht wunderschön aus [amen]
viel zu schade diese unter einem Gewebe zu verstecken Embarassed

Liebe Grüße
Johannes





Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé
Olli
Incurable Posteur
Incurable Posteur


Inscrit le: 22 Juil 2006
germany.gif

Localisation: Germany
Âge: 56 Verseau

MessagePosté le: 01/11/2019 19:53    Sujet du message: Répondre en citant

Hi Johannes,
der Rumpf und der Nasenkasten werden aber
doch beplankt Wink

Nice Work Vincent [clap] [clap]

Best Regards Olli



http://www.oliver-theede-oldtimersegler.de/
http://www.oliver-theede-oldtimersegler.de/oldtimerinteressengemeinschaft.htm


Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail Visiter le site web de l'utilisateur
bocorvin
Maniaco Posteur
Maniaco Posteur


Inscrit le: 17 Aoû 2015
netherlands.gif

Localisation: Hillegom
Âge: 77 Vierge

MessagePosté le: 01/11/2019 20:26    Sujet du message: Répondre en citant

Thanks all for the encouraging comments Very Happy

First I have to finish the construction of the wings, then all the pull-pull wires for the controls, than the canopy mold and then all the bits of ply. It will take some time!
Die rumpf ist vollig beplankt, die Flugel nur die nase, hier noch ein photo von das vorbild.





Vincent
Revenir en haut de page
Voir le profil de l'utilisateur Envoyer un message privé Envoyer un e-mail
Montrer les messages depuis:   
Poster un nouveau sujet   Répondre au sujet    RETROPLANE.net Index du Forum -> Constructions Détaillées en Photo Toutes les heures sont au format GMT + 1 Heure
Aller à la page
1, 2, 3, 4, 5, 6 Suivante
Page 1 sur 6

 
Sauter vers:  
Vous ne pouvez pas poster de nouveaux sujets dans ce forum
Vous ne pouvez pas répondre aux sujets dans ce forum
Vous ne pouvez pas éditer vos messages dans ce forum
Vous ne pouvez pas supprimer vos messages dans ce forum
Vous ne pouvez pas voter dans les sondages de ce forum
Vous ne pouvez pas joindre des fichiers
Vous pouvez télécharger des fichiers

Zone de Téléchargement du Forum et Site Retroplane


Images aléatoires album Retroplane, clic pour Agrandir

Forum en Flux RSS